Raymarine Heading Sensor User Manual

Browse online or download User Manual for GPS receiver Raymarine Heading Sensor. Raymarine Heading Sensor User Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - Handbook

Heading SensorOwner’sHandbookDocument number: 81124_3Date: 1st May 2001124_3cov.p65 09/05/01, 11:291

Page 2 - 124_3cov.p65 09/05/01, 11:292

4Heading Sensor Owner’s Handbook2.3 Fault FindingAll Raymarine products are subjected to comprehensive test andquality assurance programmes, prior to

Page 3 - Important information

5Chapter 3: InstallationChapter 3: InstallationThis chapter describes how to install the Heading Sensor, usingeveryday hand tools.3.1 Before you Begin

Page 4 - 124_3pre.p65 09/05/01, 11:292

6Heading Sensor Owner’s HandbookAlthough every effort has been taken to ensure that they will performunder all conditions, it is important to understa

Page 5 - Contents

7Chapter 3: InstallationD3548-2Connections to Other EquipmentIf your Raymarine equipment is to be connected to other equipmentusing a cable not suppli

Page 6 - 124_3pre.p65 09/05/01, 11:294

8Heading Sensor Owner’s HandbookX0.3L to 0.5L0.3L to 0.5LLLD194-2The compass is normally bulkhead mounted below decks. However, itcan be mounted above

Page 7 - Chapter 1: Introduction

9Chapter 3: Installation5. Assemble the Heading Sensor (1) to the Heading Sensor mountingbracket (4). The shaft protruding from the base of the unit m

Page 8 - 124_3c01.p65 09/05/01, 11:292

10Heading Sensor Owner’s Handbookequipment, using a suitable connector block, as shown in thediagram below. A 16.25ft (5m) NMEA accessory cable isavai

Page 9 - 2.2 Maintenance

11Chapter 4: CalibrationChapter 4: Calibration4.1 IntroductionThe Raymarine Heading Sensor must be calibrated to ensure that thetransmitted compass he

Page 10 - 2.3 Fault Finding

12Heading Sensor Owner’s HandbookTo ensure that the compass has received accurate data, perform thefollowing procedure:1. Choose a calm day, and selec

Page 11 - Chapter 3: Installation

13Chapter 4: Calibration2. If the Heading Sensor’s readings are less than the actual readings,rotate the sensor slightly clockwise.If the Heading Sens

Page 12 - Suppression Ferrites

Copyright © Raymarine Limited 2001124_3cov.p65 09/05/01, 11:292

Page 13 - 3.2 Siting the Heading Sensor

14Heading Sensor Owner’s Handbook124_3c04.p65 09/05/01, 11:3014

Page 14 - 3.3 Installation Procedure

15SpecificationHeading Sensor SpecificationDimensions: 90mm x 100mm x 130mm (3.5in x 3.9 in x 5.1in)Power Supply: 10 to 16V DCPower Consumption: 40mAO

Page 15 - 3.4 Connection Procedure

16Heading Sensor Installation Manual124_3spe.p65 09/05/01, 11:3016

Page 16

Document number: 84064-8April 2001Limited Warranty CertificateRaymarine warrants each new Light Marine/Dealer Distributor Product to be of good materi

Page 17 - Chapter 4: Calibration

Factory Service CentersUnited States of America UK, Europe, Middle East, Far EastRaymarine Inc22 Cotton Road, Unit DNashua, NH 03063-4219

Page 18 - 4.3 Heading Alignment

iPrefaceImportant informationWARNINGAlthough your Heading Sensor is designed to give accurate andreliable performance, it should serve only as an aid

Page 19

iiHeading Sensor Owner’s Handbook124_3pre.p65 09/05/01, 11:292

Page 20

iiiPrefaceContentsImportant information ... iWARNING...

Page 21 - Heading Sensor Specification

ivHeading Sensor Owner’s HandbookChapter 4: Calibration ... 114.1 Introduction ...

Page 22

1Chapter 1: IntroductionChapter 1: IntroductionThank you for purchasing a Raymarine product. We are sure yourHeading Sensor will give you many years o

Page 23 - Limited Warranty Certificate

2Heading Sensor Owner’s Handbook124_3c01.p65 09/05/01, 11:292

Page 24 - Factory Service Centers

3Chapter 2: Maintenance & Fault FindingChapter 2: Maintenance & Fault Finding2.1 Servicing and Safety• Raymarine equipment should be serviced

Comments to this Manuals

No comments