Raymarine Chartplotter User Manual Page 59
- Page / 101
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-28
RayChart 420/420D Chartplotter
The following instructions assume that the track functions are displayed.
Setting up a track
Use the track functions to switch the track on and to specify the interval at
which track points are placed. The time interval between track points can be set
to 1s, 10s, 30s, 1min, 10min or 30 minutes. The distance spacing between track
points can be set to 0.05nm, 0.1nm, 0.5nm or 1nm. The maximum track length
is 2000 points. When this limit has been reached, track points continue to be
placed, but the oldest points start to be deleted. Track ponts continue to be
placed until you switch track off; the current track is retained even when the unit
is powered off.
Setting a short time interval between track points is best suited to navigation
within a close or complex environment, eg. an estuary or marina whereas, in
contrast, a greater distance interval is best suited to a long haul voyage.
When complete, a track can be converted to and saved as a route (SmartRoute).
Refer to the setting guide shown below to determine the best setting for your
planned voyage; this is particularly important if you wish to use SmartRoute to
convert your track to a route.
33 min
5 hrs, 30 min
16 hrs, 40 min
33 hrs, 20 min
13 days, 21 hrs, 20 min
41 days, 16 hrs
100 nm
200 nm
1000 nm
2000 nm
TRACK TIME
TRACK DISTANCE
1 s
10 s
30 s
1 min
10 min
30 min
0.05 nm
0.1 nm
0.5 nm
1.0 nm
TRACK INTERVAL SETTING
Track Interval Setting Guide
D4696_1
- Raychart 420/ 2
- Chartplotter 2
- Handbook 2
- RayChart 420 and 420D 4
- Owner’s Handbook 4
- Warranty 6
- EMC Conformance 6
- Contents 8
- Table of Contents vii 10
- RayChart 420/420D 11
- Table of Contents ix 12
- Chapter 1: Overview 14
- 1.2 The chartplotter display 15
- 1.3 Operating controls 16
- Trackpad and cursor 17
- Dedicated keys 18
- Function bar 18
- Pop-up menus 19
- Database lists 19
- Chapter 2: Getting started 20
- 2.2 Switching on/off 21
- 2.3 Chart simulator 22
- 2.4 Controlling the display 23
- Note: In any display mode 24
- Moving around the chart 25
- Changing the chart scale 26
- CSR 48°30.367'N 27
- POS 1°35.636'W 27
- FIND SHIP ROUTES WAYPOINTS 27
- BRG 231°T 27
- RNG 40.91nm 27
- Inserting a Nav-Chart card 28
- Removing a Nav-Chart card 29
- Displaying the chart data 29
- Displaying chart information 29
- Chapter 3: Operation 32
- Placing a waypoint 33
- Chapter 3: Operation 3-3 34
- Selecting a waypoint 35
- Waypoint data display 36
- Editing the waypoint details 36
- Erasing a waypoint 38
- Moving a waypoint 38
- 3.3 Working with routes 39
- Creating a new route 40
- Saving the Current Route 41
- Chapter 3: Operation 3-11 42
- Erasing or (re)naming a route 43
- Editing a route 43
- Chapter 3: Operation 3-13 44
- Follow a route 46
- Reverse a route 46
- Target point arrival 47
- Alter a route 47
- Advance to a waypoint 48
- Going to an individual target 49
- Go to cursor 50
- Go to a port 50
- Stop follow or stop goto 51
- CDI display 52
- BDI display 53
- BRG 234° T 54
- RNG 12.4 nm 54
- COG 230° T 55
- SOG 6.8 Kts 55
- TIME 12:34 56
- DATE 26/01/99 56
- Displayed waypoints 57
- 3.7 Using tracks 58
- Setting up a track 59
- 3.8 Man Overboard (MOB) 60
- 4.1 Introduction 62
- 4.2 System set up parameters 62
- Bearing mode 64
- Key beep 64
- Variation 64
- Date format 64
- Time offset 65
- Language 65
- Simulator 65
- Simulated SOG 65
- Simulated COG 65
- 4.3 Chart set up parameters 66
- Orientation 68
- Plotter mode 68
- Show waypoints 68
- Waypoint symbol 68
- Autozoom 68
- Chart boundaries 70
- Depth contours <5M 70
- Depth contours 10M 70
- Depth contours >20M 70
- Position calibration 70
- 4.4 GPS setup 71
- Chapter 5: Installation 74
- Suppression ferrites 75
- 5.3 Location 76
- Panel mounting 78
- Trunnion (yoke) mounting 78
- 5.6 Cabling 80
- POWER/NMEA connector 81
- System Check 83
- Initial Switch On 83
- Chapter 5: Installation 5-11 84
- 6.1 Maintenance 86
- 6.2 Resetting the system 87
- 6.3 Problem solving 88
- 6.4 Worldwide support 89
- For accessories and parts 90
- For technical support 90
- Appendix A: Specification 92
- Appendix B: NMEA data 94
- RayChart420 95
- Installation Template 98
- 164.2 mm (6.46 in) 98
- RayChart 420 99
- Limited Warranty Certificate 100
- Stick barcode label here 101
Related products and manuals for GPS receiver Raymarine Chartplotter
GPS receiver Raymarine A60 User Manual
(50 pages)
(50 pages)
GPS receiver Raymarine Pathfinder User Manual
(111 pages)
(111 pages)
GPS receiver Raymarine GPS Kit User Manual
(24 pages)
(24 pages)
GPS receiver Raymarine 465 User Manual
(107 pages)
(107 pages)
GPS receiver Raymarine ST80 User Manual
(15 pages)
(15 pages)
GPS receiver Raymarine RAYCHART 420D User Manual
(101 pages)
(101 pages)
GPS receiver Raymarine 320 User Manual
(139 pages)
(139 pages)
GPS receiver Raymarine 300 User Manual
(136 pages)
(136 pages)
GPS receiver Raymarine DSM30 User Manual
(34 pages)
(34 pages)
GPS receiver Raymarine L365 User Manual
(83 pages)
(83 pages)
GPS receiver Raymarine GPS Plotter User Manual
(131 pages)
(131 pages)
GPS receiver Raymarine ST8001 User Manual
(54 pages)
(54 pages)
© 2020, manymanuals.com. All rights reserved. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals