Raymarine Chartplotter User Manual Page 81
- Page / 101
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5-8
RayChart 420/420D Chartplotter
GPS FunctionGPS Function
GPS FunctionGPS Function
GPS Function
ColorColor
ColorColor
Color
+12V dc Red
0V dc Black
Ground I/O White
Data in from GPS Green
Data out to GPS Yellow
POWER/NMEA connector
CAUTION:
If you do not have a breaker in your power circuit, you must fit an in-line
1A quick-blow fuse to the positive (red) lead of the power cable.
This unit is not intended for use on positive ground vessels.
The power connections should be made at a dc power distribution panel
through an isolator switch, a 1A circuit breaker or a 1A quick blow fuse. Check
that all connections are clean and tight.
The dc power system should be either:
• Negative ground, with the negative battery terminal connected to the vessel’s
ground.
• Floating, with neither battery terminal connected to the vessel’s ground.
The chartplotter is intended for use on vessels’ dc power systems operating in
the range 10.0Vdc to 18.0Vdc (ie. 12V systems, not 24V or 32V systems). A
1.5m (5ft) power cable is supplied .
If a longer power cable run is required, use the supplied power cable to connect
to the unit, then use a suitable connector block to connect the free end to the
extension cable. The supplied power cable has a cross-section of 2.0mm
2
.
Longer power cable runs may require larger wire gauges to minimise any
voltage drop in the cable. In order to determine the correct supply cable size if
the power cable must be extended, estimate the length of cable between the
vessel’s main power source and the connector block then select the wire size
indicated by the distance in the following table.
Maximum Extension Power Cable Lengths (m)
Power Cable Core mm
2
: 1.5 2.0 2.5 4.0 6.0 10.0
AWG: 16 15 14 12 10 8
Maximum extension (m) 11.0 15.0 20.0 30.0 45.0 70.0
- Raychart 420/ 2
- Chartplotter 2
- Handbook 2
- RayChart 420 and 420D 4
- Owner’s Handbook 4
- Warranty 6
- EMC Conformance 6
- Contents 8
- Table of Contents vii 10
- RayChart 420/420D 11
- Table of Contents ix 12
- Chapter 1: Overview 14
- 1.2 The chartplotter display 15
- 1.3 Operating controls 16
- Trackpad and cursor 17
- Dedicated keys 18
- Function bar 18
- Pop-up menus 19
- Database lists 19
- Chapter 2: Getting started 20
- 2.2 Switching on/off 21
- 2.3 Chart simulator 22
- 2.4 Controlling the display 23
- Note: In any display mode 24
- Moving around the chart 25
- Changing the chart scale 26
- CSR 48°30.367'N 27
- POS 1°35.636'W 27
- FIND SHIP ROUTES WAYPOINTS 27
- BRG 231°T 27
- RNG 40.91nm 27
- Inserting a Nav-Chart card 28
- Removing a Nav-Chart card 29
- Displaying the chart data 29
- Displaying chart information 29
- Chapter 3: Operation 32
- Placing a waypoint 33
- Chapter 3: Operation 3-3 34
- Selecting a waypoint 35
- Waypoint data display 36
- Editing the waypoint details 36
- Erasing a waypoint 38
- Moving a waypoint 38
- 3.3 Working with routes 39
- Creating a new route 40
- Saving the Current Route 41
- Chapter 3: Operation 3-11 42
- Erasing or (re)naming a route 43
- Editing a route 43
- Chapter 3: Operation 3-13 44
- Follow a route 46
- Reverse a route 46
- Target point arrival 47
- Alter a route 47
- Advance to a waypoint 48
- Going to an individual target 49
- Go to cursor 50
- Go to a port 50
- Stop follow or stop goto 51
- CDI display 52
- BDI display 53
- BRG 234° T 54
- RNG 12.4 nm 54
- COG 230° T 55
- SOG 6.8 Kts 55
- TIME 12:34 56
- DATE 26/01/99 56
- Displayed waypoints 57
- 3.7 Using tracks 58
- Setting up a track 59
- 3.8 Man Overboard (MOB) 60
- 4.1 Introduction 62
- 4.2 System set up parameters 62
- Bearing mode 64
- Key beep 64
- Variation 64
- Date format 64
- Time offset 65
- Language 65
- Simulator 65
- Simulated SOG 65
- Simulated COG 65
- 4.3 Chart set up parameters 66
- Orientation 68
- Plotter mode 68
- Show waypoints 68
- Waypoint symbol 68
- Autozoom 68
- Chart boundaries 70
- Depth contours <5M 70
- Depth contours 10M 70
- Depth contours >20M 70
- Position calibration 70
- 4.4 GPS setup 71
- Chapter 5: Installation 74
- Suppression ferrites 75
- 5.3 Location 76
- Panel mounting 78
- Trunnion (yoke) mounting 78
- 5.6 Cabling 80
- POWER/NMEA connector 81
- System Check 83
- Initial Switch On 83
- Chapter 5: Installation 5-11 84
- 6.1 Maintenance 86
- 6.2 Resetting the system 87
- 6.3 Problem solving 88
- 6.4 Worldwide support 89
- For accessories and parts 90
- For technical support 90
- Appendix A: Specification 92
- Appendix B: NMEA data 94
- RayChart420 95
- Installation Template 98
- 164.2 mm (6.46 in) 98
- RayChart 420 99
- Limited Warranty Certificate 100
- Stick barcode label here 101
Related products and manuals for GPS receiver Raymarine Chartplotter
GPS receiver Raymarine A60 User Manual
(50 pages)
(50 pages)
GPS receiver Raymarine Pathfinder User Manual
(111 pages)
(111 pages)
GPS receiver Raymarine GPS Kit User Manual
(24 pages)
(24 pages)
GPS receiver Raymarine 465 User Manual
(107 pages)
(107 pages)
GPS receiver Raymarine ST80 User Manual
(15 pages)
(15 pages)
GPS receiver Raymarine RAYCHART 420D User Manual
(101 pages)
(101 pages)
GPS receiver Raymarine 320 User Manual
(139 pages)
(139 pages)
GPS receiver Raymarine 300 User Manual
(136 pages)
(136 pages)
GPS receiver Raymarine DSM30 User Manual
(34 pages)
(34 pages)
GPS receiver Raymarine L365 User Manual
(83 pages)
(83 pages)
GPS receiver Raymarine GPS Plotter User Manual
(131 pages)
(131 pages)
GPS receiver Raymarine ST8001 User Manual
(54 pages)
(54 pages)
© 2020, manymanuals.com. All rights reserved. | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals