Raymarine 150/400 Installation Manual Page 77
- Page / 80
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Worldwide Warranty
The Raymarine warranty terms and conditions as described below do not affect the customer's
statutory rights.
In order to ensure that the equipment continues to operate efficiently and reliably, we
recommend that the Owner's handbook be carefully read and particular, attention is paid to
advice on safe and correct operation and use of the product. We recommend that Raymarine
equipment, be installed by an approved Raymarine installer.
Product warranty
Raymarine warrants each new product to be of good materials and workmanship. Raymarine,
or it's approved agents, will repair or exchange under warranty any parts proven to be defective
in material or workmanship under normal use, for a period of 2 years (24 months) from date of
sale to end user, or 30 months from date of shipment from Raymarine - whichever expires first,
except as provided below.
Raymarine warranty covers the parts and labour associated with any warranty repair as
described above, provided that the unit is returned to Raymarine or one of it's approved agents.
Installed warranty
In addition to the Product warranty cover as described above, Raymarine will, except as
provided below, authorise onboard warranty service by the nearest Raymarine approved
service agent, subject to maximum mileage and travel times applicable, on products, where
proof of installation, or commission by Raymarine certified installers, can be shown
The installed warranty provides for onboard repair or exchange, by Raymarine or it's approved
service agents, for a period of 2 years (24 months):either from date of sale of the boat to the end
user - where the equipment has been installed by a Raymarine certified installer, or from
commissioning of the installation by a Raymarine certified installer, or 30 months from date of
shipment of the equipment from Raymarine - whichever expires first, except as provided
below.
Obtaining warranty service
In the event of warranty service being required, contact Raymarine Technical Support or the
nearest Raymarine approved service agent - a full list of local service agents are available on the
Internet www.raymarine.com .
A suitable proof of purchase, showing date, place of purchase and serial number must be made
available to Raymarine or approved service agent at the time of request for warranty service.
In cases where a Raymarine certified installer has not installed the product; i.e. Product
warranty, the affected unit must be returned to the local Raymarine approved service agent,
with a copy of proof of purchase and/or completed warranty card. Subject to the limitations
below, the unit will be repaired/replaced at no further cost and promptly returned to the user.
In cases where the equipment has been installed by a Raymarine certified installer, (boat
builder, installer dealer etc.) i.e. installed warranty, the nearest Raymarine approved service
agent should be contacted (subject to mileage & travel time restrictions) and onboard service
requested. The warranty card, correctly completed and stamped by the installing agent, must be
available as authorisation for onboard service.
Continued . . .
- SmartPilot 1
- Commissioning 1
- Safety notices 4
- EMC Guidelines 5
- Handbook information 6
- Contents 7
- Chapter 1: System Connections 9
- 1.2 The SmartPilot computer 10
- To close 11
- S1 Systems 12
- S2 and S3 Systems 12
- 13
- Grounding the SmartPilot 15
- 1.5 Fuse Protection 16
- Securing the Cables 17
- SeaTalk B 18
- SeaTalk A 18
- SeaTalk bus 18
- Red wire not connected 19
- (Cut back and insulate) 19
- SmartPilot computer terminals 20
- NMEA connectivity overview 21
- GyroPlus yaw sensor 22
- Handheld remotes 22
- External alarm 23
- Wind vane (sail boats) 23
- Off switch (S2 and S3 only) 23
- Step 1 - Switch on 28
- Set the rudder limits 34
- 2.2 Seatrial Calibration 35
- Calibrating the compass 36
- (see below) 37
- Align the autopilot heading 38
- Save changes 38
- AutoLearn 39
- At least 0.04 nm (100 m) 40
- Start the AutoLearn 41
- Boat completes AutoLearn 41
- Save new settings 41
- Manual set-up: Non-G Systems 42
- 3.1 Calibration basics 47
- Accessing 48
- Calibration Modes 48
- 3.2 Display Calibration 49
- Display Calibration screens 50
- Data pages 51
- 3.3 User Calibration 53
- 3.4 Seatrial Calibration 53
- 3.5 Dealer Calibration 53
- Dealer Calibration 54
- SeaTrial Calibration lock 55
- Vessel type 55
- Drive type 56
- Align rudder 56
- Rudder limit 57
- Rudder gain 57
- Counter rudder 57
- Rudder damping 58
- AutoTrim 58
- Response level 59
- Turn rate limit 59
- Off course warning angle 60
- Joystick mode (PWR STEER) 60
- AutoRelease (I/O drives only) 61
- AutoTack angle 61
- Gybe inhibit 61
- Wind selection 62
- WindTrim (wind response) 62
- Cruise speed 62
- AutoAdapt 63
- Latitude 63
- System reset 64
- Dealer Calibration defaults 65
- Dealer Calibration options 66
- 4.1 Fault finding 67
- SmartPilot alarm messages 68
- 4.2 Maintenance 70
- SmartPilot Specifications 71
- WARNING: 72
- Glossary 73
- Worldwide Warranty 77
- Factory Service Centers 79
Related products and manuals for Navigational compasses Raymarine 150/400
(45 pages)© 2020, manymanuals.com. All rights reserved. | 1.699 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals