Raymarine 150/400 Installation Manual Page 130
- Page / 137
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Index 117
Location 44
NMEA connections
50
Parts supplied
43
Power supply (via SeaTalk)
49
SeaTalk connections
49
Tools required
43
K
Keypad
Functions
4
Illumination
14
L
Large cross track error warning 17
Last (previous) heading
11
Last (previous) wind
25
Latitude, Setting
96
Learn fail alarm
35
Lighting
14
Low battery alarm
35
M
Magnetic variation, Setting 86
Maintenance
37
Man overboard (MOB) warning
31
Motor/Power swapped alarm
35
N
Navigator
Connections
57
Data pages
29
NMEA
Connections 50
Data decoded by control unit
50
Inputs on control unit
51
Receiving
50
Transmitting
52
No data alarm
36
No pilot alarm
36
Non-150/400 autopilots
99–110
Adjusting autopilot settings
102–110
Commissioning the autopilot
101
Using the autopilot
100
O
Off course warning
Default angle
93
Description
10
Operating (steering) sense
58
Operating modes
Auto mode
6–13
Calibration mode
75–98
Standby mode
6
Track mode
16–22
Wind Vane mode
23–27
P
Previous (last) heading 11
Previous (last) wind
25
Product support
38
R
Response level
Default setting
85
Temporary adjustments
7–9
RG fail alarm
36
Route Completed warning
20
Rudder alignment (offset)
61, 90
Rudder bar
79
Rudder damping
92
Rudder gain
Default setting
71, 91
Temporary adjustments
27
Rudder limit, Setting
61, 91
Rudder sense, Checking
58
S
SeaTalk
Connections
49, 57
Data pages
29
SeaTalk fail 1 or 2 alarm
36
SeaTalk fail alarm
36
Seatrial
see Commissioning
Seatrial Calibration
63–73, 87
Seatrial Calibration lock
88
Self-learn calibration (AutoLearn)
70
Servicing
37
Shallow warning
31
- ST6001+ 2
- Autopilot 2
- Control Unit 2
- Owner’s 2
- Handbook 2
- Contents 4
- About this handbook 8
- Important Information 9
- EMC conformance 10
- Handbook information 10
- Using the 12
- Part 1: Using the ST6001+ 13
- Chapter 1: Introduction 14
- 1 Introduction 15
- Extended systems 15
- Chapter 2: Basic Operation 16
- 2.1 Using the control unit 17
- Display layout 18
- 2.2 Using Auto mode 19
- Port Starboard 20
- Increase 21
- Decrease 21
- Chapter 2: Basic Operation 9 22
- Off Course warning 23
- Dodging an obstacle 24
- Using sail boat features 25
- Gusty conditions 26
- 27
- 3.1 Using Track mode 29
- Exiting Track mode 30
- Cross track error 30
- Tidal stream compensation 31
- Waypoint arrival and advance 32
- Route Completed warning 33
- Dodges in Track mode 34
- Safety in Track mode 35
- About Wind Vane mode 36
- Selecting Wind Vane mode 37
- Exiting Wind Vane mode 37
- Dodges in Wind Vane mode 38
- Wind Shift warning 39
- 3.3 Adjusting the rudder gain 40
- WARNINGS: 41
- 3.4 Displaying data pages 42
- Watch timer 43
- Warning messages 44
- 3 Advanced Operation 45
- Autopilot alarm messages 48
- 4.2 General maintenance 50
- 4.3 Product support 51
- Product details table 52
- Installing the 54
- Cabling guidelines 58
- EMC installation guidelines 58
- EMC suppression ferrites 59
- 5.2 Control unit installation 60
- Flush mount control units 61
- 5.3 SeaTalk connections 62
- 5.4 NMEA connections 63
- NMEA cabling 64
- NMEA cable connectors 65
- Transmitting NMEA data 65
- Switch on 66
- SeaTalk and NMEA connections 66
- Troubleshooting 66
- 5 Installing the ST6001+ 67
- WARNING: 68
- 6.1 Dockside Checks 69
- 6 Commissioning the Autopilot 73
- 7°: if the 74
- 6.2 Seatrial Calibration 76
- Calibrating the compass 77
- Aligning the compass heading 79
- Adjusting autopilot settings 81
- Calibration Mode Overview 90
- 7.2 Display Calibration 92
- Accessing Display Calibration 93
- Data pages 1-7 94
- Accessing User Calibration 97
- Wind selection 98
- 7.4 Seatrial Calibration 100
- 7.5 Dealer Calibration 101
- Accessing Dealer Calibration 102
- Vessel type 103
- Drive type 103
- Align rudder 103
- Rudder gain 104
- Counter rudder 104
- Rudder limit 104
- Rudder damping 105
- AutoTrim 105
- Locked heading 106
- Boat heading 106
- 15˚ minimum 106
- AutoTack angle 107
- Gybe inhibit 107
- Wind type 107
- WindTrim (wind response) 107
- Cruise speed 108
- AutoAdapt 108
- Latitude 109
- Magnetic variation 109
- Autopilot reset 109
- 110
- Appendix: Using the ST6001+ 112
- With Non-150/400 Autopilots 112
- Dockside Checks 114
- Seatrial Calibration 114
- Calibration groups 115
- Appendix 116
- Dealer Calibration screens 117
- Turn rate limit 118
- Off course warning angle 119
- Power steer 119
- AutoRelease (I/O drives only) 122
- Response level 122
- Specifications 124
- Glossary 125
- Glossary 113 126
- Index 115 128
- Index 117 130
- Machine hole 132
- 90 mm (3.55 inch) 132
- Remove the shaded area 134
- Limited Warranty Certificate 136
- Factory Service Centers 137
© 2020, manymanuals.com. All rights reserved. | 2.390 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals