Raymarine 150/400 Installation Manual Page 16
- Page / 137
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
- ST6001+ 2
- Autopilot 2
- Control Unit 2
- Owner’s 2
- Handbook 2
- Contents 4
- About this handbook 8
- Important Information 9
- EMC conformance 10
- Handbook information 10
- Using the 12
- Part 1: Using the ST6001+ 13
- Chapter 1: Introduction 14
- 1 Introduction 15
- Extended systems 15
- Chapter 2: Basic Operation 16
- 2.1 Using the control unit 17
- Display layout 18
- 2.2 Using Auto mode 19
- Port Starboard 20
- Increase 21
- Decrease 21
- Chapter 2: Basic Operation 9 22
- Off Course warning 23
- Dodging an obstacle 24
- Using sail boat features 25
- Gusty conditions 26
- 27
- 3.1 Using Track mode 29
- Exiting Track mode 30
- Cross track error 30
- Tidal stream compensation 31
- Waypoint arrival and advance 32
- Route Completed warning 33
- Dodges in Track mode 34
- Safety in Track mode 35
- About Wind Vane mode 36
- Selecting Wind Vane mode 37
- Exiting Wind Vane mode 37
- Dodges in Wind Vane mode 38
- Wind Shift warning 39
- 3.3 Adjusting the rudder gain 40
- WARNINGS: 41
- 3.4 Displaying data pages 42
- Watch timer 43
- Warning messages 44
- 3 Advanced Operation 45
- Autopilot alarm messages 48
- 4.2 General maintenance 50
- 4.3 Product support 51
- Product details table 52
- Installing the 54
- Cabling guidelines 58
- EMC installation guidelines 58
- EMC suppression ferrites 59
- 5.2 Control unit installation 60
- Flush mount control units 61
- 5.3 SeaTalk connections 62
- 5.4 NMEA connections 63
- NMEA cabling 64
- NMEA cable connectors 65
- Transmitting NMEA data 65
- Switch on 66
- SeaTalk and NMEA connections 66
- Troubleshooting 66
- 5 Installing the ST6001+ 67
- WARNING: 68
- 6.1 Dockside Checks 69
- 6 Commissioning the Autopilot 73
- 7°: if the 74
- 6.2 Seatrial Calibration 76
- Calibrating the compass 77
- Aligning the compass heading 79
- Adjusting autopilot settings 81
- Calibration Mode Overview 90
- 7.2 Display Calibration 92
- Accessing Display Calibration 93
- Data pages 1-7 94
- Accessing User Calibration 97
- Wind selection 98
- 7.4 Seatrial Calibration 100
- 7.5 Dealer Calibration 101
- Accessing Dealer Calibration 102
- Vessel type 103
- Drive type 103
- Align rudder 103
- Rudder gain 104
- Counter rudder 104
- Rudder limit 104
- Rudder damping 105
- AutoTrim 105
- Locked heading 106
- Boat heading 106
- 15˚ minimum 106
- AutoTack angle 107
- Gybe inhibit 107
- Wind type 107
- WindTrim (wind response) 107
- Cruise speed 108
- AutoAdapt 108
- Latitude 109
- Magnetic variation 109
- Autopilot reset 109
- 110
- Appendix: Using the ST6001+ 112
- With Non-150/400 Autopilots 112
- Dockside Checks 114
- Seatrial Calibration 114
- Calibration groups 115
- Appendix 116
- Dealer Calibration screens 117
- Turn rate limit 118
- Off course warning angle 119
- Power steer 119
- AutoRelease (I/O drives only) 122
- Response level 122
- Specifications 124
- Glossary 125
- Glossary 113 126
- Index 115 128
- Index 117 130
- Machine hole 132
- 90 mm (3.55 inch) 132
- Remove the shaded area 134
- Limited Warranty Certificate 136
- Factory Service Centers 137
© 2020, manymanuals.com. All rights reserved. | 1.231 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals