Raymarine SeaTalk2 Setup Guide download pdf (Page 35)

Chapter 2: Installing the system 27

SeaTalk

Connections

To connect your autopilot to a SeaTalk

backbone, use a dedicated spur cable. Spur

cables are available from your Raymarine dealer, as follows:

SeaTalk

power

The Course Computer does NOT supply power for SeaTalk

. A SeaTalk

system

must be powered from its own separate power supply.

See also

For more information on SeaTalk

systems refer to the separate reference guide

available from the Raymarine web site. www.raymarine.com/handbooks.

SeaTalk

spur cable length

Part number

1 ft 3 in (400 mm) A06038,

3 ft 3 in (1 m) A06039

9 ft 10 in (3 m) A06040

16 ft 4 in (5 m) A06041

A B

D10394-1

Cut back

Screen

Red

Cut back

& insulate

Yellow

Black

White

Blue

SeaTalk

spur cable

87076_1.book Page 27 Monday, March 10, 2008 2:57 PM

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 73 74

SmartPilot X-5 1
Raymarine, SeaTalk 2
, SeaTalk 2
Contents 3
Appendix 1: NMEA 0183 sen 4
Safety notices 7
EMC Conformance 7
Pressure washing 7
Warranty 8
Product disposal 8
1.1 Installation overview 9
Product documents 10
Example SeaTalk system 11
1.3 Equipment & Tools 12
2.1 Installation requirements 15
Power cable requirement 16
Mounting 17
D10375-1 18
2.4 Mounting the SportDrive 19
/4 inch diameter. If 20
3/4 inch Steering Shaft 21
1 inch Steering Shaft 21
D10378-1 22
D10379-1 23
D10380-1 23
M4 nutM4 washer 24
M4 spring washer 24
3/4 inch shaft fitting 25
1 inch shaft fitting 26
Watertight 27
Computer 28
2.6 Fluxgate Compass 29
Mounting procedure 30
Compass connection 30
2.7 Pilot Controller 31
D10644-1 32
D10645-1 32
2.8 Connect to ground 33
2.9 Optional connections 34
Connections 35
NMEA 0183 equipment 36
2.10Final checks 37
D10396-1 37
Pilot Controllers 39
3.1 Commissioning 39
Dockside checks & setup 40
D10646-1 42
Setup map 43
Align the rudder indicator 44
Set the rudder limits 44
Seatrial calibration 45
(see below) 46
Aligning the compass heading 47
Aligning rudder bar 48
AutoLearn 48
At least 0.04 nm (100 m) 49
Boat completes AutoLearn 50
Save new settings 50
3.2 Manual setup 51
Rudder gain 52
Counter rudder 53
AutoTrim 53
Rudder damping 54
4.1 Introduction 55
Adjusting calibration values 56
4.2 Display calibration 57
Setting up data pages 58
4.3 User calibration 59
4.4 Dealer calibration 60
Vessel type 61
Drive type 62
Align rudder 62
Rudder limit 62
Response level 63
Turn rate limit 64
Off course angle 64
PowerSteer 64
Cruise speed 65
Latitude 65
System reset 65
4.5 System defaults 66
NMEA0183 to Course Computer 67
Course Computer 69
SportDrive 70
Pilot Controller (ST6002) 71

Comments to this Manuals

No comments

Raymarine SeaTalk2 Setup Guide Page 35

Comments to this Manuals

Related products and manuals for Navigators Raymarine SeaTalk2